Premium Anodised Products
premium anodised products
Ook Alumet draagt bij
aan een beter klimaat
voor in de toekomst
De noodzaak om CO2 te reduceren, materialen te hergebruiken, de opwarming van de aarde te temperen is nu algemeen bekend.
Ook Alumet wil hieraan bijdragen. Door materialen zoveel mogelijk te hergebruiken, en het toepassen van de nieuwste technieken. Door middel van onze nieuwe ultramoderne anodiseerlijn worden de nieuwste technieken gebruikt om veel minder ergie en water te gebruiken.
voordelen van anodiseren
met oog op de toekomst
Facade profile
Anodiseerlaag corrodeert
niet onder normale
omstandigheden
For premium anodized profiles it is important to have:
- The anodizing layer is transparent Good base material: Alloy in EN AW 6060 or 6063, with little variation in extrusion properties, limited extrusion lines and similar gloss.
- All profiles should be blasted before anodizing, the mechanical pre-treatment minimizes material and gloss differences and removes dye lines better than chemical alkaline etching.
- Non isolated profiles, isolation strips should be placed after anodizing. We can better mechanical pre-treat and make better electrical contact if profiles are supplied without isolation strips. This electrical contact will improve the reproduction of colour a lot! Please take notice that you will have to cut 3 cm from the ends of profile to remove clamp (contact) points.
Flat sheet
Geen vervaging
in kleur &
glansniveau
For premium anodized flat sheets it is important to have:
- Good base material is vital for premium anodized sheets. EN AW 5005 AQ (Anodizing Quality) is needed. There are several good brands with 5005 alloy from producers like Novelis, Aleris Hydro and Constellium.
- Sheets do not need blasting as pre-treatment to make them more homogenous. It is possible to blast them and make them similar to profiles. This is only possible on 3 mm thick sheets to prevent deformation during blasting process.
composite sheet
Aluminiumoxide is net zo krasbestendig als glas
For premium anodized composite sheets it is important to have:
- The anodizing layer is transparent, good base material is vital for premium anodized sheets. EN AW 5005 AQ (Anodizing Quality) is needed. Alucobond uses anodizing quality aluminium for premium anodized sheets.
- Sheets do not need blasting as pre-treatment to make them more homogenous. It is possible to blast them and make them similar to profiles.
honeycomb
Naturel geanodiseerd
aluminium houdt
de stad koel
For premium anodized honeycomb sheets it is important to have:
- The anodizing layer is transparent, good base material is vital for premium anodized sheets. EN AW 5005 AQ (Anodizing Quality) is needed. AFS uses anodizing quality aluminium for premium anodized sheets.
- Sheets do not need blasting as pre-treatment to make them more homogenous. It is possible to blast them and make them similar to profiles.
folded sheet
Vergt weinig onderhoud:
slechts 1 keer per jaar vuil
verwijderen
For premium anodized folded sheets it is important to have:
- The anodizing layer is transparent, good base material is vital for premium anodized sheets. EN AW 5005 AQ (Anodizing Quality) is needed. Famous brands are made by Novelis, Aleris, Hydro and Constellium.
- Sheets do not need blasting as pre-treatment to make them more homogenous. It is possible to blast them and make them similar to profiles.
window accessoiries
Zeer lange levensduur
van wel meer dan
80 jaar
For premium anodized accessories it is important to have:
- The anodizing layer is transparent, good base material is vital for premium anodized accessories. Window hedges are often made of EN AW 6060 alloy, which is no problem to anodize. Door handles are more difficult, as they are often made of cast alloys.
- Door handles cannot be brushed or polished in Alumet, we do not have the machines to perform these operations on small parts, blasting is possible.
